High Pressure Sour spec 3Phase Inlet sep line leater unit. This unit is fully flanged and includes extensive controls.

Line heater is a 2.5MMBTU 900#, c/w Profire 1100 burner management system

(1) complete unit combined with steam turbine

11,840 MW Gas turbine / 7 MW steam turbine

18,840 total MW plant 

Gas fired

Waste Heat Recovery Boiler

Turbine engine:

Manufacturer:                     Solar Turbines INC, San Diego USA Model:        Titan 130 with SoLoNOx combustion,

Packager:                              Turbomach

Year of Manufacture:         2005

Operating hours:                 about 15.500 (whole plant), 150 starts

Was operated until 2007, after that standby

Condition:                             fully serviced by Turbomach and ready for start.

Capacity:                              11.840 kW

Speed:                                    11.215 RPM continual

Fuel:                                      Natural Gas with input pressure of 28 bar

Fuel /gas consumption:      around 3.700 Nm³/h (calorific value 10.4 kWh/m³)

 Burners:                               14

Start system:                        electro. Hydraulic, 110 kW

Outlet temperature:                                       486°C Exhaust gas volume:                            131.000m³/h

Dimensions:                          longitudinal-and transverse-force bases

Turbine:                                9m x 2,2m x 2,8m = 33 tons

Strainer:                               4m x 2,9m x 3,8m = 4.8 tons Insulating dome:           9m x 2,2m x 3,25m = 7 tons

Mounting:                             On steel skid (with acoustic enclosure)

Reduction Gearbox

type:                                     Solar Epicyclic Reduction Gearbox

Output rpm:                         1500

Year Manufactured:           2005

Generator

Manufacturer:                     Leroy Somer

Type / Model:                       LSA 58 BMCL 14-4P.

Frequency:                            50 Hz

Voltage:                                 5.25 kV

Power:                                   14.800 kVA, PF = 0.8

Speed:                                    1500

Year manufactured:            2005

Speed                                     1.500 RPM     max. 1.800 RPM

Power:                                         9.000 kVA

      Fire protection system

Control systems turbine

Turbomach TTS3

Auxiliaries

Lubrication System Fuel System

Start System electro-hydraulic 110 kW Air inlet system, 1 stage air filter system Exhaust system complete with silencer

Waste Heat Recovery Boiler

Manufacturer:                     IEG, Livice (Slovakia)

Type:                                     Natural circulation boiler with additional firing 2 modules of finned tubes

Steam with add. Burner:     44.5 t/h, max. 47 t/h             - 58 bar, 510°C, O2 14.8% Steam without add. Burner 18.5 t/h              - 58 bar, 440°C, O2 15.7% Burner:              3 burners with 730 Nm³ each at full load

Fuel:                                      Natural Gas H

Cal. Value:                            10.4 kWh/m³

Gas pressure input:                                             3.5 Bara

Chimney

Type                                       two-layered, inside stainless steel

Dimension:                           40 m high, exhaust 3.8 m²

Exhaust temp.                      220°C (limited with compensator)

Feed water system

Pumps:                                  30 t/h, 75 bar,

3 x 50%, one in reserve

Steam turbine

Type:                                     B+V, MARC2 – B10, back pressure with extraction Live steam pressure                  58 bar 60.5 bar max

Live steam temp.:                                        510°C

Steam quantity:                                              45 t/h

Extraction pressure:            21 bar                                               24.0 bar max Extraction temp.:                 383°C                                               490°C max Extraction quantity:            7 t/h                                               15 t/h max Exhaust pressure:                3 bar               4 bar max Exhaust temp. :     180°C                                               262°C max Exhaust quantity:                28 t/h                                               47 t/h max Speed:                                    10.043 RPM

Quick closing speed:                                       11.047 RPM

Plant is in excellent condition,

Maintained and serviced by Turbomach on regular basis, boiler and steam turbine dry and hot conserved. Ready for immediate start of dismantling

Unit is inside 8x9' seacan

This unit was assembled in China.  

- Manufacturer: Wartsila

- Series 220, 1200RPM, 2925 KW Mec

- Serial numbers: 281004 through 281008

- Year built: 1999 (281008 was built in 2000)

- Hours of operation:

 --281004 = 1719 hrs 

 --281005 = 1602 hrs  

 --281006 = 1762 hrs  

 --281007 = 1537 hrs  

 --281008 = 1702 hrs

One (1) Solar Taurus 70 Gas Engine skid consists of following:
-Solar outdoor enclosure, S/N TG00502, assembly 2-58881, Built 2000 dismantled
2019. ISO rating turbine continuous 7250 KWe (15 deg C/59 deg F, sea level, heat rate 10,650
kJ/kwe-hr/10,100 btu/kw-hr, thermal efficiency 32.8% , exhaust gas mass flow 98,900
kg/hr/215,840 lbs/hr at 490 deg C/910 deg f/ Turbine speed 15,200 rpm. Peak rating ISO 7628
kw. Site rating 6363 kw summer 90 Deg F, 25 PPM NOX and CO
Package hours and 2500 846 starts
-Engine Solar Taurus 70s, Version 9701S, S / N 00658. SoLoNOX, Natural gas
-Gear unit Solar Epicyclic, 13600 hp, ratio 8.21005, 15158/1800 rpm, Service factor 1.10,
Assembly no. 33085C-200, Serial no. SGK99-55329. With starting motor
-Sound attenuated enclosure , doors 85 DBA noise level. Axial side exhaust, top inlet air, inlet 4”
natural gas all associated accessories
One (1) Solar Generator skid consist of following:
-Kato synchronous AC generator, continuous rating 7200 kw, 9000 kw, voltage 12470 -13800 v
0.8 pf, 417 amps, 3 PHASE, 60 HZ, S/N 13937-01, Code 4P12-3600, Model No
A269660001
-Brushless exciter field amps 5, field volts 100, PMG 240 v, 180 hz
-Generator terminal box with 4 x 500:5 cts on phase side, neutral side 3x600:5 cts, 1 x 100:5 ct
-Solar Turbotronic control panel mounted side of enclosure

ADDITIONAL EQUIPMENT
One (1) set of bolts with nuts for Engine skid and generator skid
One (1) Gearbox to generator coupling with coupling guard, coupling bolts and nuts both sides
One (1) Air inlet system with ductwork, filter house, supporting structure.
One (1) Exhaust system with exhaust expansion joint, silencer, stack (total height of stack 38’6”)
One (1) Fire cylinder cabinet and control panel
One (1) Lube oil cooler
One (1) Engine skid enclosure air inlet duct
One (1) Engine skid enclosure air exhaust duct
One (1) Generator air inlet filter with duct
One (1) Generator air exhaust duct
One (1) Lube oil fume vent duct with fan
One (1) Power Ohm resister 200 amps, 10 secs neutral ground resister
One (1) Outdoor Electrical house consist of following:
-Generator breaker control panel with 1200 amps Siemens type 13-GMI-750-1200-58 circuit
breaker, 125 VDC trip and close, Beckwith M-3425 generator protection relay,
2 x 12,470:120 V pts on bus side, 2 x 12,470:120 V generator side, voltage regulator,
3 x 600:5 cts bus side
-Reliant 200 hp VFD for starting motor, 480 v

-Cutler Hammer MCC, 800 amps, 480 v
-Switchgear battery charger Constant Power Mfg co USGS-120-1PH-120-10, 120 vac in,
120 vdc, 10 amp dc out
-Turbine battery charger American battery charger model ABC11-120-20, 208-240 v ac in 120
Vdc 20 amps dc out.
-Batteries (advisable not to take it, because of age)
-Spare parts - filters, consumables etc.
One (1) Refurbished (purchased 2001) Universal Compression Arial JGR-2 natural gas compressor skid
100 psig inlet and 300 psig outlet
One (1) Station transformer padmount GE 750 kva, 12500 v to 480 v
One (1) set of walkways ladders
One (1) set of manuals and drawings
 

Engine Data Tag Model No: CENTAUR 50 Version: 6201 GSC

Engine I.D: HDODAA-1100-007

Serial No: 1022H

Power: (G/L): 4600 kWe/NA

NGP (RPM): 14944 50 Hz / 14951 60 Hz NPT (RPM): NA

IGV Setting: +5.0

^T5 Base (G/L): 1280 F. /NA

Setpoint (G/L): T5 1250 F. / NA Full load

Reduction Gear Box Data Tag

Assembly: 302750-201

Serial: MAR11-94457

Gear Type: EPICYCLIC Ratio: 8.305921

Rated Power: 8,700 HP

Rated Input Speed: 14, 951 RPM Rated Output Speed: 1,800 RPM Overload Factor: 1.1

Considering the low hours and starts on these units, and also taking into consideration that the starts on these units, and also taking into consideration that the system is a Variable Frequency Drive (VFD), which renders smooth start and ramping, it is not expected to see much wear (if any) on the gearboxes. A general visual inspection was made from a distance with lighting and everything appeared clean and intact.

SKID-

* 6" @ 8.2 Channel Iron -Periphery & Support Beams
* 3/16" Checkered Plate -Flooring
* 2-7/8" -Pull Bars Both Ends
* 3" Poly-Urethane Foam -Under-Skid Insulation

49,800 lbs

Features of the existing units:

• Packages are available immediately, and ready for transport. (Central Alberta)
• 3Pc skid
• Frame, cylinders and motors have been removed and stored under strict manufactures guidelines
• Deferred Ariel Warranty available upon request
• Full engineering studies and document packages available(Torsional and Acoustical) 
• The existing units are fully flanged including a high amount of control and sensing transmitters.
• CRN’s for AB and BC are existing
• Sour Spec NDE PWHT and 1.8 C.A. on all pressure vessels and cooler sections
• Sweet gas purge packing system including seal pot and vacuum pump.
• Piping designed with 1/16” C.A.
• Suction, side stream, bypass and blowdown valves.
• Allen Bradly Control Logix panel
• Glycol heating system
• Motor Ventilation system

Note on Sour Service: Some/all of the existing piping system may meet 1/8” piping minimum thicknesses and can be assessed on a case by case basis based on design conditions. A reclassification and or retrofit of some of the piping system is possible to comply with full sour.

Package NDE meets or exceeds code and is aligned with industry standard code for sour service.

6600V, 531Amps,3phase, 60HZ Continuous duty rated RPM 896 

Frame 10840, Model B774921

Enclosure WP II

Comes with air induction ducting, TB woods 2000-28 coupler and Ariel KBZ flywheel with hub

VFD Controlled speed 600-900 RPM

Cooler Weight: 23000lbs, Recirc system available if needed. Will require seperate truck for transport.

• Brand New Cummins. KTA50-G3.

Please see all the attachements for full specs, conditions, running/working conditions, power, consumption and more.

Generator Set Type: Stand-By

Engine Model: G3516

Fuel Type: Natural Gas

Voltage: 2400/4160

Model: G3516

Panel: with Autostart and Safety Shutdowns

Frequency: 60 Cycles/Hz

Phase: Three Phase

11.1 compression ratio

Hours:

• Running Hours: 15,841, 13977, 15,010, 6,582, 6213, 13,892, 12,013, 14,000,

Price is in CANADIAN DOLLARS. Unit FOB: EUROPE

(Location is for approximate location ONLY, unit may have been relocated - FOB Europe)

Air-X-Changers 144EH-102-22

Cooler is new surplus and available for an excellent price.

Designed for Wauk 3524GSI - single stage gas section 350psig mawp.

The cooler could be re sectioned for a trim cooling application and or other compression application.

Units come complete with Two years of spares and all special tools.

Complete engineering data package available.

Recent inspection Data from Siemens

Full installation and commissioning available to buyer.

See attached document for technical specification

**Units must be exported - Cannot be used in USA**

PRICE INCLUDES DISMANTLING, PACKING and TRANSPORTING TO THE NEAREST INTERNATIONAL PORT

GTG's are controlled via the local solar supplied PLC

Units Were installed in 2013 but notcommissioned, Units have been presered in coordinance of manufaturer recomendations.

Solar has carried out a recent condition assessment report May 2018 and is available

Donaldson TTD air inlet system

Generators are ABB AMS 100LM, 11KV, 22789 KVA